غلامحسین مجذوبی

استاد

تاریخ به‌روزرسانی: 1403/07/12

غلامحسین مجذوبی

مهندسی / مهندسی مکانیک

مقالات علمی چاپ شده در مجلات

  1. "Characterization of a functionally graded material produced using anew designed blender"
    كاوه رحماني, Gholam Hossein Majzoobi, d r
    PHYSICA SCRIPTA, Vol. , 2024
  2. "Tribological behaviour of Ti/HA and Ti/SiO2 functionally graded materialsfabricated at different strain rates"
    Gholam Hossein Majzoobi, كاوه رحماني, مستوره محمدي, حامد بختياري, Sajeewa S. N. Maharachchikumbura
    Biotribology, Vol. , 2023
  3. "A Study of the Functionally Graded (Magnesium/Titanium Dioxide) Material's Mechanical and Tribological Characteristics Fabricated at Various Compaction Loading Rates"
    كاوه رحماني, Gholam Hossein Majzoobi
    TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, Vol. , 2023
  4. "Determination of the parametersof material models using dynamicindentation test and artificial neuralnetwork"
    سمانه پورالعجل, Gholam Hossein Majzoobi
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, Vol. , pp.501-514, 2023
  5. "An Investigation Into the Synergistic Effect of CAPVD Cr/CrN NanolayeredCoating Deposition and Hard-Anodizing Methods on Fretting Fatigue Life of 7075-T6 Aluminum Alloy"
    Gholam Hossein Majzoobi, حسين عسگري بختياري, Hassan Elmkhah
    TRIBOLOGY TRANSACTIONS, Vol. , 2023
  6. "On the effect of Cr/CrN nanolayered coating deposited by Arc-PVD methodon axial fretting fatigue behavior of Al7075-T6 alloy"
    حسين عسگري بختياري, Gholam Hossein Majzoobi, Hassan Elmkhah
    SURFACE & COATINGS TECHNOLOGY, Vol. , 2023
  7. "Microstructural examination and mechanical characterization of Ti/HA andTi/SiO2 functionally graded materials fabricated at different loading rates"
    Gholam Hossein Majzoobi, مستوره محمدي, كاوه رحماني
    Journal of the Mechanical Behavior of Biomedical Materials, Vol. , 2022
  8. "Influence of normal load frequency on fretting fatigue behaviour by acritical plane-based approach"
    فرشاد عباسي, Gholam Hossein Majzoobi, Sabrina Vantadori, ِAndrea Zanichelli, Davide Leonetti, Geovanni Pio Pucilo
    INTERNATIONAL JOURNAL OF FATIGUE, Vol. , 2022
  9. "Thermal properties of Mg-B4C micro and nanocomposites fabricated by static and dynamic compaction methods"
    كاوه رحماني, Gholam Hossein Majzoobi, حامد عسگري, Ali Sadooghi
    TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, Vol. , 2022
  10. "A study on damage evolution in Cu–TiO2 composite fabricated usingpowder metallurgy followed by hot extrusion"
    Gholam Hossein Majzoobi, سيدسجاد جعفري, كاوه رحماني
    MATERIALS CHEMISTRY AND PHYSICS, Vol. , 2022
  11. "Effect of projectile nose on high‐velocity impact behavior of fiber metal laminates"
    Gholam Hossein Majzoobi, محمد كشفي, محمد عرفان رياض الحسيني, Mohsen K. Keshavarz
    POLYMER COMPOSITES, Vol. , pp.1177-1185, 2022
  12. "Incorporation of the effect of strainrate in Mie-Gruneisen equation of statefor polyethylene"
    Gholam Hossein Majzoobi, نيلوفر زارع
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, Vol. , pp.38-46, 2022
  13. "A comparative and experimental study on performances of Natural gas-Air Combustion, Helium, and Air as Propellants in a Gas Gun"
    شهاب الدين زارعي, Gholam Hossein Majzoobi, Hossein Ahmadikia
    COMBUSTION SCIENCE AND TECHNOLOGY, Vol. , pp.682-699, 2022
  14. "An Investigation into the Effect of Strain Rate on Damage Evolution in Pure Copper Using a Modified BonoraModel"
    سيدسجاد جعفري, Gholam Hossein Majzoobi
    Journal of Stress Analysis, Vol. , pp.127-138, 2021
  15. "Comprehensive study on quasi-static and dynamic mechanical propertiesand wear behavior of Mg–B4C composite compacted atseveral loading rates through powder metallurgy"
    كاوه رحماني, Gholam Hossein Majzoobi, محمد كشفي, ghasem ebrahimi
    TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, Vol. , pp.1-11, 2021
  16. "A study on damage evolution in Cu-TiO2 composite fabricated atdifferent temperatures and strain rates"
    سيدسجاد جعفري, Gholam Hossein Majzoobi
    Materials Research Express, Vol. , pp.1-25, 2021
  17. "On the effect of compaction velocity, size, and content of reinforcingparticles on corrosion resistance of Mg–B4C composites"
    كاوه رحماني, Gholam Hossein Majzoobi, حامد بختياري, Ali Sadooghi
    MATERIALS CHEMISTRY AND PHYSICS, Vol. , 2021
  18. "Determination of stress–strain curves of materials at high strain rates using dynamic indentation technique"
    سمانه پورالعجل, Gholam Hossein Majzoobi
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, Vol. , pp.327-356, 2021
  19. "The Effect of Pre-compaction on Properties of Mg/SiC Nanocomposites Compacted at High Strain Rates"
    محمد كشفي, Gholam Hossein Majzoobi, كاوه رحماني
    Journal of Stress Analysis, Vol. , pp.19-28, 2020
  20. "The effect of particle size on microstructure, relative density and indentation load of Mg-B4C composites fabricated at different loading rates"
    كاوه رحماني, Gholam Hossein Majzoobi
    JOURNAL OF COMPOSITE MATERIALS, Vol. , 2020
  21. "A review of the effects of cyclic contact loading on fretting fatigue behavior"
    فرشاد عباسي, Gholam Hossein Majzoobi, Joseba Mendiguren
    Advances in Mechanical Engineering, Vol. , 2020
  22. "Mechanical and physical characterization of Mg-TiO2 and Mg-ZrO2 nanocomposites produced by hot-pressing"
    كاوه رحماني, Gholam Hossein Majzoobi, Ali Sadooghi, محمد كشفي
    MATERIALS CHEMISTRY AND PHYSICS, Vol. , 2020
  23. "Mechanical characterization of Mg-B4C nanocomposite fabricated at different strain rates"
    Gholam Hossein Majzoobi, كاوه رحماني
    International Journal of Minerals Metallurgy and Materials, Vol. , pp.252-263, 2020
  24. "Simultaneous effects of strain rate and temperature on mechanical response of fabricated Mg–SiC nanocomposite"
    كاوه رحماني, Gholam Hossein Majzoobi, َA Atrian
    JOURNAL OF COMPOSITE MATERIALS, Vol. , pp.659-668, 2020
  25. "Mechanical characterization of graphene oxide reinforced epoxy at different strain rates"
    Gholam Hossein Majzoobi, شهاب اميني نژاد, seyed alireza Sabet
    POLYMER ENGINEERING AND SCIENCE, Vol. , 2019
  26. "A new cooperative model for the prediction of compressive yield stress of polycarbonate nanocomposites considering strain rate, temperature, and agglomeration"
    Gholam Hossein Majzoobi, حسين ملك محمدي, پاينده پيمان جواد
    JOURNAL OF COMPOSITE MATERIALS, Vol. , pp.3567-3575, 2019
  27. "The effect of compaction loading rate on hardness and wearresistance of Mg–B4C nanocomposite"
    كاوه رحماني, Gholam Hossein Majzoobi
    Materials Research Express, Vol. , 2019
  28. "Determination of length to diameter ratio of the bars in torsional Split Hopkinson bar"
    Gholam Hossein Majzoobi, كاوه رحماني, S. Lahmi
    MEASUREMENT, Vol. , pp.144-154, 2019
  29. "Performance of a Two-stages Gas Gun: Experimental, Analytical and Numerical Analysis"
    Gholam Hossein Majzoobi, محمدحسين قايدرحمتي, محمد كشفي
    International Journal of Engineering, Vol. , 2019
  30. "Role of sonication time on mechanical properties of graphene oxide/epoxy nanocomposites under quasi-static loading conditions"
    شهاب اميني نژاد, Gholam Hossein Majzoobi, seyed alireza Sabet
    IRANIAN POLYMER JOURNAL, Vol. , pp.895-908, 2019
  31. "Investigation of microstructure effect on fretting fatigue crack initiation using crystal plasticity"
    k MINAII, Gholamhossein Farrahi, Morad Karimpour, Hamid Bahai, Gholam Hossein Majzoobi
    FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES, Vol. , pp.640-650, 2019
  32. "Role of graphene oxide and sonication time on mechanical properties of epoxy nanocomposites at high strain rate"
    Gholam Hossein Majzoobi, شهاب اميني نژاد, seyed alireza Sabet
    Materials Research Express, Vol. , 2019
  33. "Experimental and numerical study of high strain rate property of pure copper processed by ECAE method"
    S Sulaiman, jamshid nemati, Gholam Hossein Majzoobi, M. AlJermi
    Advances in Materials and Processing Technologies, Vol. , pp.386-393, 2019
  34. "A new overall nonlinear damage model for fiber metal laminatesbased on continuum damage mechanics"
    محمد كشفي, Gholam Hossein Majzoobi, Nicola Bonora, Gianluca Iannitti, Andrew Ruggiero, Ehsan Khademi
    ENGINEERING FRACTURE MECHANICS, Vol. , pp.21-33, 2019
  35. "Mechanical characterization of polycarbonate reinforced with nanoclay and graphene oxide"
    حسين ملك محمدي, Gholam Hossein Majzoobi, جواد پاينده پيمان
    POLYMER COMPOSITES, Vol. , pp.3947-3959, 2019
  36. "Development of a new technique for measuring damage accumulation at high strain rates"
    سيدسجاد جعفري, Gholam Hossein Majzoobi, Ehsan Khademi, محمد كشفي
    ENGINEERING FRACTURE MECHANICS, Vol. , pp.162-172, 2019
  37. "Estimation of axial fretting fatigue life at elevated temperatures using critical distance theory"
    Gholam Hossein Majzoobi, پرويز اژدرزاده
    SURFACE REVIEW AND LETTERS, Vol. , 2018
  38. "An Experimental Investigation into Wear Resistance ofMg-SiC Nanocomposite Produced at High Rate of Compaction"
    Gholam Hossein Majzoobi, كاوه رحماني, َA Atrian
    Journal of Stress Analysis, Vol. , pp.35-45, 2018
  39. "A new constitutive bulk material model to predict the uniaxial tensile nonlinear behavior of fiber metal laminates"
    Gholam Hossein Majzoobi, محمد كشفي, َAlexsandre Bonora, احسان خادمي, Gianluca Lattinni, Andrew Ruggiero
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, Vol. , pp.26-35, 2018
  40. "Temperature effect on mechanical and tribological characterization of Mg-SiC nanocomposite fabricated by high rate compaction"
    Gholam Hossein Majzoobi, كاوه رحماني, َA Atrian
    Materials Research Express, Vol. , 2018
  41. "An investigation into the effect of elevated temperatures on fretting fatigue response under cyclic normal contact loading"
    فرشاد عباسي, Gholam Hossein Majzoobi
    THEORETICAL AND APPLIED FRACTURE MECHANICS, Vol. , pp.144-154, 2018
  42. "A novel approach to calibrate the Drucker–Prager Cap model for Al7075 powder"
    َA Atrian, Gholam Hossein Majzoobi, Bernd Markert, Seyed Hassan Nourbakhsh
    ARCHIVE OF APPLIED MECHANICS, Vol. , pp.1859-1876, 2018
  43. "A novel approach for dynamic compaction of Mg–SiC nanocomposite powder using a modified Split Hopkinson Pressure Bar"
    كاوه رحماني, Gholam Hossein Majzoobi, َA Atrian
    POWDER METALLURGY, Vol. , pp.164-177, 2018
  44. "The effect of aluminum and titanium sequence on ballistic limit of bi-metal 2/1 FMLs"
    Gholam Hossein Majzoobi, حميد مرشدي, K Farhadi
    THIN-WALLED STRUCTURES, Vol. , pp.1-7, 2018
  45. "Damage characterization of aluminum 2024 thin sheet for different stress triaxialities"
    Gholam Hossein Majzoobi, محمد كشفي, َAlexsandre Bonora, Gianluca Lattinni, Andrew Ruggiero, احسان خادمي
    Archives of Civil and Mechanical Engineering, Vol. , pp.702-712, 2018
  46. "Effect of out-of-phase loading on fretting fatigue response of Al7075-T6 under cyclic normal loading using a new testing apparatus"
    فرشاد عباسي, Gholam Hossein Majzoobi
    ENGINEERING FRACTURE MECHANICS, Vol. , pp.93-111, 2018
  47. "Developing a new experimental set up to study fretting fatigue behaviorunder cyclic contact loading"
    فرشاد عباسي, Gholam Hossein Majzoobi, Mohammad Mehdi Barjesteh
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY, Vol. , pp.1-14, 2017
  48. "Numerical and experimental study of ballistic response of kevlar fabric and kevlar/epoxy composite"
    Gholam Hossein Majzoobi, فايزه محمدظاهري
    International Journal of Engineering, Vol. , pp.791-799, 2017
  49. "Effect of Contact Pressure On Fretting Fatigue Behavior under Cyclic Contact Loading"
    Gholam Hossein Majzoobi, فرشاد عباسي
    SURFACE REVIEW AND LETTERS, Vol. , pp.1-17, 2017
  50. "Experimental and analytical investigations into the effects of inorganic filler on the polypropylene nanocomposite microhardness"
    پاينده پيمان جواد , Gholam Hossein Majzoobi, Reza Bagheri
    JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS, Vol. , pp.1484-1502, 2017
  51. "A study on fiber metal laminates by using a new damage model for composite layer"
    محمد كشفي, Gholam Hossein Majzoobi, َAlexsandre Bonora, Gianluca Lattinni, Andrew Ruggiero, احسان خادمي
    INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, Vol. , pp.75-80, 2017
  52. "On the effect of shot-peening on fretting fatigue of Al7075-T6 under cyclic normal contact loading"
    Gholam Hossein Majzoobi, فرشاد عباسي
    SURFACE & COATINGS TECHNOLOGY, Vol. , pp.292-303, 2017
  53. "Determination of the constants of GTN damage model using experiment, polynomial regression and kriging methods"
    Foad Rahimidehgolan, Gholam Hossein Majzoobi, Farhad Alinejad, Jalal Fathi Sola
    Applied Sciences-Basel, Vol. , 2017
  54. "On the Effect of Contact Geometry on Fretting Fatigue Life Under Cyclic Contact Loading"
    Gholam Hossein Majzoobi, فرشاد عباسي
    TRIBOLOGY LETTERS, Vol. , 2017
  55. "A strain range dependent cyclic plasticity model"
    Ehsan Khademi, Gholam Hossein Majzoobi, Nicola Bonora
    International Journal of Engineering, Vol. , pp.321-329, 2017
  56. "The Ballistic Behavior of High Strength, Low Alloy-100 Steel at Sub-zeroTemperatures"
    Gholam Hossein Majzoobi, S. Moradi
    International Journal of Engineering, Vol. , pp.1747-1756, 2016
  57. "Characterization of mechanical properties of Al-6063deformed by ECAE"
    Gholam Hossein Majzoobi, jamshid nemati, Mohammad Kazem Pipelzadeh, S Sulaiman
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, Vol. , 2016
  58. "Evaluation of tensile strength of Al7075-SiC nanocomposite compactedby gas gun using spherical indentation test and neural networks"
    Sayyed Hassan Nourbakhsh Shourabi, Seyyed Ali Gallehdari, Reza Masoudi Nejad, َA Atrian, Gholam Hossein Majzoobi
    ADVANCED POWDER TECHNOLOGY, Vol. , pp.1821-1827, 2016
  59. "Deriving parameters of pressure-dependent yield surface for polymericcomposites using kriging-based optimization method"
    Gholam Hossein Majzoobi, جواد پاينده پيمان, Reza Bagheri
    مهندسی مکانیک مدرس, Vol. , pp.280-290, 2016
  60. "Experimental and numerical studies on the effect of deep rollingon bending fretting fatigue resistance of Al7075"
    احسان خادمي, Gholam Hossein Majzoobi, فرج الله زارع جونقاني
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, Vol. , 2016
  61. "Determination of the extendedDrucker–Prager parameters using thesurrogate-based optimization methodfor polypropylene nanocomposites"
    جواد پاينده پيمان, Gholam Hossein Majzoobi, Reza Bagheri
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, Vol. , pp.220-232, 2016
  62. "Ductile to brittle failure transition of HSLA-100 Steel at high strain rates and subzero temperatures"
    Gholam Hossein Majzoobi, Amir Hossein Mahmoudi, S. Moradi
    ENGINEERING FRACTURE MECHANICS, Vol. , pp.179-193, 2016
  63. "Effect of densification rate on consolidationand properties of Al7075–B4C compositepowder"
    Gholam Hossein Majzoobi, َA Atrian, Mohammad pipelzadeh
    POWDER METALLURGY AND METAL CERAMICS, Vol. , pp.1-11, 2015
  64. "Effect of equal channel angular extrusion on Al−6063 bending fatiguecharacteristics"
    jamshid nemati, Gholam Hossein Majzoobi, S Sulaiman, B.T.H.T Baharudin, M.A Azmah Hanim
    International Journal of Minerals Metallurgy and Materials, Vol. , 2015
  65. "A constitutive model for hardnessconsidering the effects of strain, strainrate and temperature"
    Gholam Hossein Majzoobi, جمال محمدي, stephan hardy, Mohammad pipelzadeh, Saeed lahmi
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, Vol. , pp.284-298, 2015
  66. "An Experimental Investigation on the Strain Rate Sensitivityof a Severely Deformed Aluminum Alloy"
    Faramarz Fereshteh-Saniee, سعيد سپاهي بروجني, Saeed lahmi, Gholam Hossein Majzoobi
    EXPERIMENTAL MECHANICS, Vol. , 2015
  67. "Tribological properties of Al7075-SiC nanocomposite prepared byhot dynamic compaction"
    Gholam Hossein Majzoobi, َA Atrian, mohammad hossein enayati
    COMPOSITE INTERFACES, Vol. , pp.1-17, 2015
  68. "Experimental modeling ofstrain-dependent cyclic plasticity forprediction of hysteresis curve"
    Gholam Hossein Majzoobi, َAlexsandre Bonora, ِDomenico Gentile, احسان خادمي
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, Vol. , pp.314-324, 2015
  69. "Determination of the constants of cap model for compaction of threemetal powders"
    Gholam Hossein Majzoobi, شهيده جان نثاري لاداني
    ADVANCED POWDER TECHNOLOGY, Vol. , pp.928-934, 2015
  70. "A comparative study on hot dynamic compaction and quasi-static hotpressing of Al7075/SiCnp nanocomposite"
    حامد بختياري, Gholam Hossein Majzoobi, mohammad hossein enayati, َA Atrian
    ADVANCED POWDER TECHNOLOGY, Vol. , pp.73-82, 2015
  71. "Fretting Fatigue Life Estimation of Al 7075-T6 UsingPlain Fatigue Test"
    Gholam Hossein Majzoobi, k MINAII
    TRIBOLOGY TRANSACTIONS, Vol. , pp.613-621, 2015
  72. "A new approach for the correctionof stress–strain curves after neckingin metals"
    Gholam Hossein Majzoobi, فرزاد فريبا, Mohammad pipelzadeh, stephan hardy
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, Vol. , pp.1-13, 2014
  73. "Warm dynamic compaction of Al6061/SiCnanocomposite powders"
    Gholam Hossein Majzoobi, حامد بختياري, َA Atrian, stephan hardy, Mohammad pipelzadeh
    J Materials: Design and Applications, Vol. , pp.1-13, 2014
  74. "Determination of the Constants of Material Models Using Inverse Taylor Test"
    Gholam Hossein Majzoobi, پوريا كاظمي
    EXPERIMENTAL TECHNIQUES, Vol. , pp.1747-1567, 2014
  75. "A New Technique based on Strain Energy for Correction of Stress-strain Curve"
    Gholam Hossein Majzoobi, farzad fariba
    International Journal of Engineering, Vol. , pp.1287-1296, 2014
  76. "Improvement of performance of bolt-nut connections, Part II: Experimental investigation"
    Gholam Hossein Majzoobi, M Agh Mohammad Dabbagh, P asgari, Mohammad pipelzadeh, SJ hardy
    journal of Mechanical Engineering Science, Vol. , pp.1-12, 2014
  77. "Numerical implementation of a new coupled cyclic plasticityand continum damage model"
    N bonora, Gholam Hossein Majzoobi, احسان خادمي
    COMPUTATIONAL MATERIALS SCIENCE, Vol. , pp.538-547, 2014
  78. "Mechanical and microstructural characterization of Al7075/SiC nanocompositesfabricated by dynamic compaction"
    َA Atrian, Gholam Hossein Majzoobi, m.h Enayati, h Bakhtiari
    International Journal of Minerals Metallurgy and Materials, Vol. , 2014
  79. "Improvement of performance of bolt-nut connections, part I: Simulations"
    Gholam Hossein Majzoobi, M Agh Mohammad Dabbagh, P asgari, Mohammad pipelzadeh, SJ hardy
    journal of Mechanical Engineering Science, Vol. , 2014
  80. "Determination of the constants ofmaterial models at high strain ratesand elevated temperatures using shotimpact test"
    Gholam Hossein Majzoobi, alireza hossein khani, Saeed lahmi, Mohammad pipelzadeh, stephan hardy
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, Vol. , pp.342-351, 2013
  81. "A New Investigation on the Effect of Re-shot Peeningon Fretting Fatigue Behavior of A17075-T6"
    Gholam Hossein Majzoobi, محمدعلي كاظمي
    TRIBOLOGY TRANSACTIONS, Vol. , pp.943-952, 2013
  82. "بررسی آزمایشگاهی اثر دما و نرخ کرنش بر رفتار مکانیکی و تورق گلار 1خمشی"
    علی شیرافکن، غلامحسین مجذوبی، محمد کشفی
    مهندسی ساخت و تولید، نسخه ، صفحات:37-47، 1402
  83. "مطالعه عددی- تجربی اثر نرخ کرنش بر خواص کششی نانوکامپوزیت های گرافن- اپوکسی"
    شهاب امینی نژاد، غلامحسین مجذوبی، سید علیرضا ثابت
    مهندسی مکانیک مدرس، نسخه ، صفحات:497-506، 1398
  84. "بررسی تجربی و تحلیلی رفتار فشاری نانوکامپوزیت پلی کربنات تقویت شده با نانو رس و گرافن اکسید در نرخ کرنش پائین"
    حسین ملک محمدی، غلامحسین مجذوبی، جواد پاینده پیمان
    علوم و فناوری کامپوزیت، نسخه ، صفحات:427-434، 1398
  85. "بررسی اثر درصد نانو SiC و دما بر رفتار دینامیکی و استاتیکی نانوکامپوزیت Mg-SiC ساخته شده با متالورژی پودر"
    کاوه رحمانی، غلامحسین مجذوبی
    مهندسی مکانیک مدرس، نسخه ، صفحات:361-368، 1397
  86. "مطالعه اثر جنس و ضخامت لایه میانی بر جذب انرژی شبه استاتیکی ورق های فلزی الیافی"
    الهام انصاری، غلامحسین مجذوبی، کاوه رحمانی، محمد کشفی
    علوم و فناوری کامپوزیت، نسخه ، صفحات:427-436، 1397
  87. "تعیین پارامترهای سطح تسلیم وابسته به فشار برای کامپوزیت های پلیمری به روش بهینه سازی بر پایه مدل کریجینگ"
    جواد پاینده پیمان، رضا باقری، غلامحسین مجذوبی
    مهندسی مکانیک مدرس، نسخه ، صفحات:280-290، 1395
  88. "بررسی تجربی، عددی و تحلیلی میکروسختی نانوکامپوزیت های پلی پروپیلن"
    پاینده پیمان جواد ، غلامحسین مجذوبی، رضا باقری
    علوم و فناوری کامپوزیت، نسخه ، صفحات:165-176، 1395
  89. "مطالعه عددی توزیع تنشهای پسماند در فرایند غلتکزنی عمیق آلومینیوم 707"
    فرج الله زارع جونقانی، غلامحسین مجذوبی، احسان خادمی
    مهندسی مکانیک مدرس، نسخه ، صفحات:426-434، 1394
  90. "بررسی تاثیر نرخ کرنش بر الگوی خمیری شابوش"
    غلامحسین مجذوبی، سمانه پورالعجل، احسان خادمی
    مهندسی مکانیک مدرس، نسخه ، صفحات:9-16، 1393
  91. "بررسی آزمایشگاهی تاثیر دما و میزان نانوذرات بر خواص نمونه های نانوکامپوزیتی Al6061-SiC تولید شده به روش تراکم دینامیکی گرم"
    غلامحسین مجذوبی، حامد بختیاری، امیر عطریان
    نانو مواد، نسخه ، صفحات:141-152، 1393
  92. "بررسی اثرسخت شوندگی سینماتیکی در اتوفرتاژ استوانه های جدار ضخیم"
    رحمن سیفی، غلامحسین مجذوبی، حفیظ الله بنی اسد
    مهندسی مکانیک شریف، نسخه ، صفحات:75-81، 1393

مقالات علمی ارائه شده در همایش‌ها

  1. "DETERMINATION OF TENSILE AND SHEAR STRENGTHS USING A NEW TEST SPECIMEN"
    Gholam Hossein Majzoobi, farhan khodaee
    AMPT 2014 Advances in materials and processing technology, 2014
  2. "A Study on the Optimum Locations of Mounting Strain Gauges onTorsional Split Hopkinson Bar"
    كاوه رحماني, Gholam Hossein Majzoobi
    AMPT 2014 Advances in materials and processing technology, 2014
  3. "Evaluation of mechanical properties of Al7075/SiC Nanocomposite Fabricated by Hot Uniaxial Pressing"
    Gholam Hossein Majzoobi, حامد بختياري, َA Atrian
    5th international conference on nanostructures (ICNS5), 2014
  4. "The Effect of Pre-compaction on Dynamic Compaction Process of Al/SiC Nanocomposite Powder"
    Gholam Hossein Majzoobi, َA Atrian, حامد بختياري
    The Bi-annual International Conference on Experimental Solid Mechanics and Dynamics (X-Mech-2014), 2014
  5. "A new technique for determination of the constants of Zerilli-Armstrong material model at high strain rates and elevated temperatures"
    Gholam Hossein Majzoobi, alireza hossein khani, Saeed lahmi
    The Bi-annual International Conference on Experimental Solid Mechanics and Dynamics (X-Mech-2014), 2014
  6. "Determination of the constants of Zerilli-Armstrong model using inverse Taylor test"
    Gholam Hossein Majzoobi, پوريا كاظمي
    The Bi-annual International Conference on Experimental Solid Mechanics and Dynamics (X-Mech-2014), 2014
  7. "DETERMINATION OF LENGTH TO DIAMETER RATIO IN TORSIONAL SPLIT HOPKINSON BAR"
    Gholam Hossein Majzoobi, كاوه رحماني, Saeed lahmi
    The Bi-annual International Conference on Experimental Solid Mechanics and Dynamics (X-Mech-2014), 2014
  8. "بررسی اثر دما بر رفتار مکانیکی و تورق ورقه های فلزی الیافی تحت بار خمشی"
    غلامحسین مجذوبی، علی شیرافکن، محمد کشفی
    نوزدهمین همایش ملی و هشتمین همایش بین المللی ساخت و تولید، 1401
  9. "مطالعه آزمایشگاهی رفتار کششی ورق های فلزی الیافی 2/1 و 3/2 به کمک DIC"
    البرز محبی، غلامحسین مجذوبی، محمد کشفی
    نوزدهمین همایش ملی و هشتمین همایش بین المللی ساخت و تولید، 1401
  10. "بررسی آزمایشگاهی رفتار کششی و خمشی ورق های فلزی الیافی ساخته شده به روش پرس تخت داغ"
    البرز محبی، غلامحسین مجذوبی، محمد کشفی
    سومین کنفرانس کامپوزیت در صنایع ایران، 1401
  11. "تعیین مدل ماده خمیری چرخه ای آلومینیوم 2024 با استفاده از شبیه سازی تکراری و الگوریتم ژنتیک"
    محمد کشفی، غلامحسین مجذوبی، احسان خادمی، نیکولا بونورا، جانلوکا یانیتی، اندرو روجیرو، کاوه رحمانی
    بیست و پنجمین کنفرانس سالانه بین المللی مهندسی مکانیک ایران، 1396
  12. "تحلیل اجزاء محدود سه بعدی میدان تنش پسماند ناشی از جوشکاری در اتصال لولهای صلیبی شکل"
    نبرد حبیبی، ملیحه حیران، غلامحسین فرهی، غلامحسین مجذوبی، امیرحسین محمودی
    ISME نوزدهمین همایش سالانه مهندسی مکانیک ایران،، 1393